OFF - FOR SALE: Manley Snappers w/ New Tubes and Updated Capacitors
Item #649200567Info: Manley Snappers w/ New Tubes and Updated Capacitors
||Cash, Paypal, Cheque, Money Order, Money Wire, Interac/EMT
||40.82 (kg) Calculate Shipping
||55.88cm x 48.26cm x 50.80cm
||7 - Good (?)
May 10, 18 6:57am (PST)
Edited: Aug 01, 18 10:50am
TX, United States
rushbattle has a verified PayPal account.Verified in United States
|Days in System:||84|
- Allow Local Pickup
United States: $40.00
Sponsored post - log in to remove this ad.
** This Ad is Marked as OFF by seller and cannot be responded to. **
These Manley Snappers were the fortieth pair they made. They do not have the triode switch, which Manley actually discourages anyhow, but it does have the option for 600 ohm inputs. That option is great for pro audio applications and long interconnect runs. They are in good shape, and come with nearly new tubes in all positions. Less than 20 hours on the whole set of tubes: new production Tung-Sol 12AT7, GE 5687, Electro-Harmonix 6CA7.
The power supply capacitors were replaced with OEM parts exactly. There was nothing wrong with the original caps, but I did it as a preventative measure. They are very expensive to replace, it was over 600 dollars for both monoblocks. The new caps did not change the sound of the monoblocks, so the ones that were replaced were totally fine. Under 20 hours on the new PS e-caps.
The six MultiCap film caps in the each monoblock were replaced with Mundorf Silver/Gold in Oil in exactly the same value capacitance as the stock film caps. I initially thought there was little change in the sound, but after breaking in they definitely have made an improvement.
I will split PayPal fees and will only charge actual shipping amount unless you buy it now. I am happy to use your shipping account so you can be sure it is the correct amount.
If you are curious, the reason I am selling them is because I bought some horn-loaded speakers and I am trying SET next. Thank you for looking and reading the ad!
From Manley Website:
Features and Specifications
100 Watt partial triode (UltraLinear) EL-34 output stage is tolerant of a wider variety of output load conditions than pure pentode.
Precise and balanced signal path from input to output. Circuit self-balances with either single-ended or balanced inputs. [Don't let either speaker terminal contact chassis, earth or any other ground.
Switch-selectable RCA unbalanced inputs, or XLR balanced inputs. RCA jack input impedance about 330 kOhms, XLR 15 kOhms. If one input is not occupied, the input selector switch may then be used as a poor-man's MUTE switch. Handy for checking the bias, swapping input cables, etc..
Input Sensitivity RCA jack: 750 mV RMS for full output into 5 Ohms
Input Sensitivity RCA jack: 71 mV RMS for 1 watt output into 8 Ohms
Input Sensitivity XLR jack: 1.5 V RMS for full output into 5 Ohms
Overall voltage gain RCA jack to Output: 31 dBu, or about 32 volts per volt.
Signal to A-weighted noise ratio on Humberto's bench is about 110 dB.
Damping Factor: 4.7
All-balanced amp topology keeps B+ voltage variations from degrading the performance of the input and driver stages. This technique can help make a push-pull amplifier very revealing of signal detail, in part by canceling power-supply-related perturbations and increasing signal-to-noise ratios.
Portly 180 Joule energy storage reservoir in the main B+ supply channel for explosive transient response and athletic musical stamina. Also reduces B+ fluctuations due to varying current demands of output stage.
Wideband transformerless balanced input with bridged 15 kOhm input impedance. Balanced input sensitivity may be selected by changing one resistor to suit whatever operating level may be required. 0 dBu, +4, +8, etc... If desired, the user may safely ground either pin 2 or 3 for single-ended drive of the balanced XLR input... [Be careful NOT to drive pins 2 and 3 of the XLR with a large common-mode signal, or the internal B+ fuse could blow.]
Quiet DC supply for the input and driver tube filaments.
Excellent square-wave response, and very low excess phase-shift with frequency.
Amp actually puts out 110W @ 5 Ohm load @ 2 kHz @ onset of clipping, 117 VAC mains voltage, 3.5 amps mains current.
100 W spec: 15 Hz - 40 kHz into 5 Ohms
Puts out 100W into an 8 Ohm load.
Snapper unit weight: 38 lbs.
Features and Specifications
Input Impedance RCA: 475 kOhm
Input Impedance XLR: 15 kOhm (or 600 Ohm switchable on units before MSN524)
Input Sensitivity RCA: 750mV input = 110W output
Input Sensitivity XLR @ 15 kOhms: 1.5 V input = 110W output
Input Sensitivity XLR @ 600 Ohms: 2.4 V input = 110W output (w/600 Ohm source)
Gain RCA: factory set for 31 dB; Range = 29.5 to 34.5dB
Gain XLR: factory set for 25 dB
Negative Feedback: factory set for 9dB of global NFB
Maximum Output Power into 5 Ohms: 110 Watts (1.5% THD @ 1kHz)
Maximum Output Power into 8 Ohms: 100 Watts (1.5% THD @ 1kHz)
Signal to Noise Ratio Ref. 1W: Typically 90 dB A-WGT 20-20K
Noise Floor: Typically 105V = -77dBu A-WGT; Typically 388V = -66dBu unweighted
Will Scratch Your Floor: Use pennies under pointed feet to avoid marring cabinetry. Try quarters if you are in upper tax brackets. The bargain performer would be nickels. Paper currency does not function as well. Euro coins work 1.54 times better.
Dynamic Range: 98dB
THD+noise @ 1W: less than 0.1%
Frequency Response at 110W full power: 15 Hz to 40 kHz FLAT
Frequency Response at 5W into 5 Ohms: 10 Hz to 65 kHz FLAT, -3dB @ 100KHz
Recommended Speaker Load: Optimized for 5 Ohms
Actual Output Impedance: 1.5 Ohms
Power Consumption (idle): 170 Watts (1.4A @120VAC)
Power Consumption (at Full Power 110W): 336 Watts (2.8A @120VAC)
Operating Mains Voltage: Factory set for 100V, 120V or 220-240VAC operation for original destination country's mains voltage.
Operating Mains Voltage: changeable with power transformer re-wiring and fuse value change.
Mains Voltage Frequency: 50~60Hz
Input Vacuum Tube: 1 x 12AX7 Russian with 6CA7 or KT77 output tubes; use 12AT7EH large plate Electro-Harmonix Russian with EL34 types
Driver Vacuum Tube: 1 x 7044 or 5687 GE JAN NOS
Output Vacuum Tubes: 4 x 6CA7 (or EL34 equavalent)
B+ Voltage: 570V DC
Output Tube Quiescent Standing Current: 30mA
Set Bias for: 300mVDC measured across 10 Ohm cathode resistor
Lamp type: "FuseLamp" size 1/4" X 1 1/4", 12 volt, 0.15 amp; Units built after 5/2003 use white LEDs
Fuse values & types for: 120VAC operation: MDL or MDA 5 AMP / 250 Volt SLO-BLO size 1/4" X 1 1/4"
240VAC operation: MDL or MDA 3.15 AMP/ 250 Volt SLO-BLO size 1/4" X 1 1/4" B+ FUSE: MDA 1/2 AMP, 250 Volt SLO-BLO CERAMIC BODY size 1/4" X 1 1/4"
Dimensions: 15" deep x 13" wide x 8.75" tall
Shipping weight each: 45 pounds
This ad was originally posted on US Audio Mart and the seller ships to the United States.
Similar items you might be interested in
Canuck Audio Mart is FREE!